Crestron CLW-SLVS1RF Specifications download pdf

infiNET™ SWITCHES

Introduction

Features and Functions

The CLW-SW1RF (-SW1RF) and CLW-SW4RF

(-SW4RF) are stand-alone wall box switches that can also

act as wireless infiNET™ devices that report to a

Crestron

control processor through an infiNET gateway

such as the Crestron C2N-MNETGW.

These switches are a part of Crestron’s line of lighting

products using infiNET mesh network technology. infiNet

technology is “Wi-Fi” friendly and provides fault

tolerance and increased effective signal strength as

network devices are added.

Up to 30 infiNET devices (including C2N-MNETRPT

infiNET Repeaters) can communicate with one

C2N-MNETGW Gateway. If more devices are needed,

more C2N-MNETGW gateways may be added to a

Cresnet

network.

Crestron Electronics, Inc. Installation Guide - DOC. 6293C

15 Volvo Drive Rockleigh, NJ 07647 (2011322)

The infiNET switches operate on the 2.4 GHz “ISM

band” (2400 MHz to 2483.6 MHz) at 10 mW. The output

power of these devices allow RF signals to travel

approximately 150 feet indoors and 250 feet outdoors

(subject to site-specific conditions) without the use of

repeaters or other infiNET devices. The range is

dependent on construction of the building, obstructions,

and RF interference from other devices. The location of

the switch is an important factor in determining RF

performance. Adding more infiNET devices or repeaters

to the network effectively increases the range, strength,

and reliability of the network.

The -SW1RF and -SW4RF feature a three-position mode

selection switch. For more information, refer to the latest

version of the infiNET Switches Operations Guide (Doc.

6397) which is available from the Crestron website

(www.crestron.com/manuals). In the absence of control

system communications, the switch can still be used to

control the attached load.

The CLW-SWS1RF (-SWS1RF) and CLW-SWS4RF

(-SWS4RF) are similar to the -SW1RF and -SW4RF

(respectively) with the added capability of working with a

slave unit (CLW-SLVS1RF) in a multi-switch / single

circuit application.

The CLW-SLVS1RF (-SLVS1RF) is a slave unit that

when used in conjunction with the -SWS1RF or the

-SWS4RF acts as an additional switch control point in a

multi-switch / single circuit application. It does not

connect to a Cresnet system and cannot be used without a

-SWS1RF or -SWS4RF. The -SLVS1RF does not have a

mode selection switch. It will emulate the RUN mode of

the -SWS1RF (even if connected to a -SWS4RF) unless

the mode selection switch of the master is set to “OFF”.

For more information, refer to the latest version of the

infiNET Switches Operations Guide (Doc. 6397) which is

available from the Crestron website.

These switches are available in a variety of colors and

textures. The table below shows the availability.

Available Colors/Textures

COLOR/

TEXTURE

MODEL NUMBER

SUFFIX

MATCHING LUTRON

FACEPLATE

White W Not Applicable

Smooth White W-S CW-1-WH

Almond A CW-1-LA

Smooth Almond A-S CW-1-LA

Black B Not Applicable

Smooth Black B-S CW-1-BL

Specifications

Following are specifications for the -SW1RF, -SW4RF,

-SWS1RF, -SWS4RF, and -SLVS1RF.

CLW-SW1RF/-SW4RF, CLW-SWS1RF/-SWS4RF, &

CLW-SLVS1RF Specifications

SPECIFICATION DETAILS

Power Requirements Line Power, 120 VAC, 60 Hz

Operating Frequency 2400 MHz to 2483.6 MHz

(802.15.4 compliant)

RF Output Power 10 mW

Operating Ranges¹

Typical Distance

Indoors

(without repeater)

Typical Distance

Outdoors

150 ft

250 ft

(subject to site-specific

conditions)

Default MNET ID SW1RF/SW4RF: 01/01

SWS1RF/SWS4RF: 01/01

Switch Type Single-Pole, Single-Throw

Load Type Incandescent, Tungsten-

Halogen, Fluorescent / High

Intensity Discharge (HID),

Electronic Low Voltage,

Magnetic Low Voltage, Neon /

Cold Cathode, Ceiling Fan

2-Series Control System

Update File

2,3

Version 3.154 or later

Load Ratings

Incandescent /

Tungsten-Halogen

-SW1RF/-SW4RF: 1000W

-SWS1RF/-SWS4RF: 1000W

-SLVS1RF: N/A

Magnetic Low Voltage

-SW1RF/-SW4RF:

1000VA/750W

-SWS1RF/-SWS4RF:

1000VA/750W

-SLVS1RF: N/A

(Continued on following page)

Tel: 888.CRESTRON 03.09

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

1 2 3 4 5 6 7 8 9 10

Summary of Contents

Page 1 - Introduction

infiNET™ SWITCHES Introduction Features and Functions The CLW-SW1RF (-SW1RF) and CLW-SW4RF (-SW4RF) are stand-alone wall box switches that can also

Page 2 - Physical Description

infiNET™ SWITCHES This page is intentionally left blank. 10 • infiNET™ Wall Box Switch : CLW-SW1/4RF, SWS1/4RF, & SLVS1RF Installation Gu

Page 3

infiNET™ SWITCHES CLW-SW1RF/-SW4RF, CLW-SWS1RF/-SWS4RF, & CLW-SLVS1RF Specifications (continued) SPECIFICATION DETAILS Load Ratings (continue

Page 4 - Multigang Installations

infiNET™ SWITCHES Physical view of CLW-SW1RF/SWS1RF (clockwise from top; Top, Side, and Front) 1.75 in(4.45 cm)2.38 in(6.03 cm)3.28 in(8.32 cm)3.81

Page 5 - Installation

infiNET™ SWITCHES RF Exposure (OET Bulletin 65) To comply with FCC's RF exposure limits for general population / uncontrolled exposure, this

Page 6 - Testing

infiNET™ SWITCHES Derating Information for Fluorescent/HID Applications Part Number No Side Removed One Side Removed Two Sides Removed -SW1RF/ -SW4R

Page 7 - Problem Solving

infiNET™ SWITCHES for operation of the LED. If the neutral is not available, the white lead should be capped off. 3. Push all power wires back in

Page 8 - Return and Warranty Policies

infiNET™ SWITCHES b. Press and hold the top or bottom of the button on the -SW1RF/-SWS1RF or any button on the -SW4RF/-SWS4RF. Problem Solving Trou

Page 9 - Appendix: Wiring Diagrams

infiNET™ SWITCHES Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or servi

Page 10

infiNET™ SWITCHES Appendix: Wiring Diagrams Following are wiring diagrams for circuits that may be found when installing infiNET switches: Stand-Alo

Crestron CLW-SLVS1RF Specifications

Browse online or download Specifications for Network switches Crestron CLW-SLVS1RF. Crestron CLW-SLVS1RF Specifications User Manual

Summary of Contents

More documents for Network switches Crestron CLW-SLVS1RF

Comments to this Manuals

Crestron CLW-SLVS1RF Specifications

Browse online or download Specifications for Network switches Crestron CLW-SLVS1RF. Crestron CLW-SLVS1RF Specifications User Manual

Summary of Contents

More documents for Network switches Crestron CLW-SLVS1RF

Comments to this Manuals

Related products and manuals for Network switches Crestron CLW-SLVS1RF