Crestron SWAMP(I)-24X8 Specifications Page 29
- Page / 60
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Crestron SWAMP(I)-24X8 Sonnex™ Multiroom Audio System
For more information, refer to “Set Bus Assignment” which starts on page
31, “Bridge Outputs” which starts on page 32, or the Sonnex Tools help
file.
4.
Use Sonnex Tools or the SWAMP-24X8’s “Installer Mode” menu to set the
subwoofer output to Mono.
For more information, refer to “Set Mono/Stereo” which starts on page 29
or the Sonnex Tools help file.
5.
Trim the subwoofer using an SPL meter, the pink noise files (satellite pink
noise.wav and subwoofer pink noise.wav) found in the Sonnex Tools help
file, and Sonnex tools.
NOTE: The audio output of the PC used to configure the system should be
connected to an input on the SWAMP-24X8. The input should be routed to
the connected outputs. For information on routing signals, refer to
“Operation” on page 47.
a. Set the SPL meter to C-Weighted, Slow Response.
b.
Place the SPL meter at the listening position with the meter pointing
straight up.
c.
Play satellite pink noise.wav on the left speaker.
d.
Turn the volume up until the SPL meter reads 85 dB.
e.
Play satellite pink noise .wav on the right speaker. The SPL meter
should read very close to 85 dB.
f.
Play subwoofer pink noise.wav on the left speaker.
g.
Use Sonnex Tools or the “Installer Mode” menu to adjust the bus
volume offset of the subwoofer zone until the SPL meter reads 85 dB.
For more information, refer to the Sonnex Tools help file or “Set Bus
Volume Offset” which starts on page 31.
Connect to SWAMPE Sonnex
Multiroom Audio Expander or
S-EXT1-S Sonnex Link Over
Fiber Extender
The SWAMP-24X8 can be connected to a SWAMPE Sonnex Multiroom Audio
Expander or S-EXT1-S Sonnex Link Over Fiber Extender via shielded CAT5e cable
to increase the number of output zones. Up to eight SWAMPE Sonnex Multiroom
Audio Expanders or eight S-EXT1-S Sonnex Link Over Fiber Extenders (connected
to a SWAMPE Sonnext Multiroom Audio Expander) can be connected to one
SWAMP-24X8.
NOTE: When connecting a SWAMP-24X8 to a peripheral, Crestron recommends
using Crestron DM-CBL-8G or high-quality CAT5e shielded twisted-pair cable.
Shielded connectors such as the DM-8G-CONN must be used.
NOTE: When the SWAMP-24X8 is connected to a control system by Cresnet, only
one SWAMPE Multiroom Audio Expander or one S-EXT1-S Sonnex Link Over
Fiber Extender (connected to a SWAMPE Multiroom Audio Expander) can be
connected.
Operations Guide – DOC. 7049B Sonnex™ Multiroom Audio System: SWAMP(I)-24X8 • 23
- Crestron SWAMP(I)-24X8 1
- Operations Guide 1
- Important Safety Instructions 2
- WARNING: 2
- IMPORTANT: 2
- Regulatory Compliance 3
- Contents 5
- Sonnex™ Multiroom Audio 7
- System: SWAMP(I)-24X8 7
- Introduction 7
- Features and Functions 8
- Bonus Zones 9
- Plug and Play Expansion 9
- Advanced DSP 9
- Speaker Profiles 10
- Output Bussing 10
- Passive Subwoofer Support 11
- Ultimate Integration 11
- Applications 12
- Specifications 13
- SPECIFICATION DETAILS 14
- Physical Description 16
- (191 mm) 18
- (178 mm) 18
- Pin 3 Pin 4 19
- Pin 2 Pin 1 19
- Network Wiring 22
- Sonnex Link Wiring 22
- Identity Code 22
- Installation 23
- Hardware Hookup 25
- + - G + 26
- Bridging Outputs 27
- ” which starts on page 31 29
- Configuration 31
- Gain Control 32
- EQ Setting 33
- Bass Setting 34
- Treble Setting 34
- Loudness Setting 34
- Balance Setting 35
- Mono/Stereo Setting 35
- Minimum Volume Setting 36
- Maximum Volume Setting 36
- Startup Volume Setting 36
- Bus Setting 37
- Offset Setting 37
- Bus Display 38
- Bridging Setting 38
- Wattage Setting 39
- Impedance Setting 39
- Speaker Protect Setting 40
- Crestron DRC Setting 40
- Confirm Global EQ Setting 40
- IP Address 42
- Subnet Mask 42
- Default Router 43
- DHCP Setting 43
- WINS Setting 43
- Front Panel Lock Settings 44
- Cresnet ID Setting 45
- IP ID Setting 45
- Control System IP Address 45
- Programming Software 47
- Uploading and Upgrading 50
- PC Running 51
- Crestron Toolbox 51
- SWAMP-24X8 51
- Program Checks 52
- Operation 53
- Problem Solving 54
- Cable Length Equation 55
- Future Updates 56
- Return and Warranty Policies 57
- Tel: 888.CRESTRON 01.12 60
Related products and manuals for Receiver Crestron SWAMP(I)-24X8
Receiver Crestron DM-RX1-1G User Manual
(4 pages)
(4 pages)
Receiver Crestron QM-RMCRX-BA Specifications
(76 pages)
(76 pages)
Receiver Crestron SP-1 User Manual
(14 pages)
(14 pages)
Receiver Crestron SP-1 Specifications
(24 pages)
(24 pages)
Receiver Crestron ABVR-1 Specifications
(16 pages)
(16 pages)
Receiver Crestron CNXRMIRD Specifications
(36 pages)
(36 pages)
Receiver Crestron SP-1 User Manual
(14 pages)
(14 pages)
Receiver Crestron CNXRMIRD User Manual
(12 pages)
(12 pages)
© 2020, manymanuals.com. All rights reserved. | 0.388 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals